CHAPTER 11
1
Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?
UBAMA# configure terminal
UBAMA(config)# line vty 0 4
UBAMA(config)# line console 0
UBAMA(config)# interface Serial 0/0/0
**UBAMA(config)# interface FastEthernet 0/1
2
In a Cisco router, when do changes made to the running-configuration take effect?
after a system restart
as the commands are entered
when logging off the system
**when the configuration is saved to the startup-configuration
3
Refer to the exhibit. A technician applies the configuration in the exhibit to a clean router. To verify the configuration, the technician issues the show running-config command in the CLI session with the router. What lines should the technician expect to see in the router output from the show running-config command?
enable password class
line console 0
password ccna
enable secret cisco
enable password class
line console 0
password ccna
enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0
enable password class
line console 0
password ccna
enable secret cisco
enable password 7 14141E0A1F17
line console 0
password 7 020507550A
**enable secret 5 $1$v0/3$QyQWmJyT7zCa/yaBRasJm0
enable password 7 14141E0A1F17
line console 0
password 7 020507550A
4
When network services fail, which port is most often used to access a router for management purposes?
AUX
Ethernet
**Console
Telnet
SSH
5
Refer to the exhibit. A network administrator on HostA has problems accessing the FTP server. Layer three connectivity testing was successful from HostA to the S1 interface of RouterB. Which set of commands will allow the network administrator to telnet to RouterB and run debug commands?
RouterB(config)# enable secret class
RouterB(config)# line vty 0 4
RouterB(config-if)# login
RouterB(config)# enable secret class
RouterB(config)# line vty 0 2
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
**RouterB(config)# enable secret class
RouterB(config)# line vty 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-line)# password cisco
RouterB(config-line)# login
RouterB(config)# enable secret class
RouterB(config)# line aux 0
RouterB(config-vty)# password cisco
RouterB(config-vty)# login
6
Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?
show running-config
show startup-config
**show interfaces
show ip route
show version
show memory
7
Refer to the exhibit. Which names correctly identify the CLI mode represented by the prompt for Switch-East4#? (Choose two.)
line configuration mode
user executive mode
**global configuration mode
privileged executive mode
interface configuration mode
**enable mode
8
What command is used to change the default router name to Fontana?
Router# name Fontana
Router# hostname Fontana
Router(config)# name Fontana
**Router(config)# hostname Fontana
9
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
**Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
**Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
**Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
10
Refer to the exhibit. The output is shown for the show ip route command executed on Router A. What does the IP address 192.168.2.2 represent?
Gateway for the 192.168.1.0 network
Gateway for the 192.168.3.0 network
IP assigned to the serial port on Router A
**IP assigned to the serial port on Router B
11
Refer to the exhibit. What additional command is required to allow remote access to this switch?
NA-SW1(config-if)# no shutdown
NA-SW1(config)# enable password password
**NA-SW1(config)# ip default-gateway address
NA-SW1(config-if)# description description
12
Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration. From privileged EXEC mode, which of the following commands can the administrator use for this purpose? (Choose two.)
show flash
show NVRAM
**show startup-config
**show running-config
show version
13
Which three terms correctly define the forms of help available within the Cisco IOS? (Choose three.)
hot keys
**context-check
context-sensitive
**structured check
command override
**command syntax check
14
Refer to the exhibit. A student is responsible for the IP addressing, configuration and connectivity testing of the network shown in the graphic. A ping from host B to host C results in a destination unreachable but a ping from host B to host A was successful. What two reasons could account for this failure based on the graphic and partial router output for the Dallas router? (Choose two.)
The host A is turned off.
The Fa0/0 interface on Dallas is shutdown.
The LAN cable is disconnected from host B.
**The S0/0/1 IP address of Dallas is improperly configured.
**The Fa0/0 interface on Dallas is in a different subnet than host B.
The clock rate is missing on the serial link between Dallas and NYC.
15
Which combination of keys would be used at the CLI prompt to interrupt a ping or traceroute process?
**Ctrl-C
Ctrl-P
Ctrl-R
Ctrl-Shift-6
Ctrl-Z
16
The connection between routers B and C has been successfully tested. However, after rebooting router C, the administrator noticed the response time between networks 10.10.3.0 and 10.10.4.0 is slower. Ping between the two routers is successful. A trace route indicates three hops from router B to router C. What else can be done to troubleshoot the problem?
Ping router B S0/1 connection from router C.
Trace the connection between router B to router C S0/1.
Issue a show ip route command in router B to verify routing is enabled.
**Issue a show interfaces command on router C.
17
In a Cisco device, where is the IOS file stored prior to system startup?
RAM
ROM
**Flash
NVRAM
18
On a Cisco router, which interface would be used to make the initial configuration?
toinen
19
A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a router to manage it. Which access method should be chosen?
Telnet
Console
AUX
**SSH
Rabu, 07 Mei 2008
CCNA 1 - Module 10 Exam Answers
CHAPTER 10
1
Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)
connecting a PC to a router's console port
**connecting two routers together via their fast ethernet ports
**connecting two switches together at gigabit speeds
connecting a PC to a switch at Gigabit Ethernet speeds
connecting two devices with the same interface type at Fast Ethernet speeds
2
Which three statements are true about the role of routers in the network? (Choose three.)
They propagate broadcasts.
They enlarge collision domains.
They segment broadcast domains.
**They interconnect different network technologies.
**Each router interface requires a separate network or subnet.
**They maintain a common frame format between LAN and WAN interfaces.
3
Refer to the exhibit. A network administrator has decided to use packet capture software to evaluate all traffic from the student subnet on the way to the Internet. To ensure that all packets are captured, what network device should be used to connect the monitoring station to the network between R1 and R2?
**router
hub
switch
wireless access point
4
A network administrator is required to use media in the network that can run up to 100 meters in cable length without using repeaters. The chosen media must be inexpensive and easily installed. The installation will be in a pre-existing building with limited cabling space. Which type of media would best meet these requirements?
STP
**UTP
coaxial
single-mode fiber
multimode fiber
5
Refer to the exhibit. Which three statements are true about the exhibited topology? (Choose three.)
Hosts B and C are in the same subnet.
**Five broadcast domains are present.
**Host B is using a crossover cable to connect to the router.
Four broadcast domains are present.
xFive networks are shown.
Host B is using a rollover cable to connect to the router.
6
Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Choose three.)
RJ 11
**DB 60
**Winchester 15 pin
DB 9
**smart serial
RJ 45
7
How many host addresses may be assigned on each subnetwork when using the 130.68.0.0 network address with a subnet mask of 255.255.248.0?
30
256
**2046
2048
4094
4096
8
Refer to the exhibit. Based on the IP configuration shown, what would be the result of Host A and Host B attempting to communicate outside the network segment?
both host A and B would be successful
**host A would be successful, host B would fail
host B would be successful, host A would fail
both Host A and B would fail
9
Refer to the exhibit. What destination IP address will PC1 place in the header for a packet destined for PC2?
192.168.1.1
192.168.2.1
192.168.2.2
192.168.3.1
**192.168.3.54
10
Refer to the exhibit. Which three statements identify the type of cabling that would be used in the segments that are shown? (Choose three.)
Segment 1 uses backbone cabling.
**Segment 1 uses a patch cable.
Segment 3 uses patch cabling.
Segment 3 uses vertical cabling.
**Segment 3 uses horizontal cabling.
**Segment 4 uses vertical cabling.
11
A company is planning to subnet its network for a maximum of 27 hosts. Which subnet mask would provide the needed hosts and leave the fewest unused addresses in each subnet?
255.255.255.0
255.255.255.192
**255.255.255.224
255.255.255.240
255.255.255.248
12
Refer to the exhibit. A student is setting up a home network primarily used for extensive file transfers, streaming video, and gaming. Which network device is best suited to these types of activities in the topology shown?
wireless access point
router
hub
**switch
13
Refer to the exhibit. How many subnets are required to support the network that is shown?
2
**3
4
5
14
What does the term "attenuation" mean in data communication?
**loss of signal strength as distance increases
time for a signal to reach its destination
leakage of signals from one cable pair to another
strengthening of a signal by a networking device
15
To establish a console connection from a computer to a Cisco router, which cable wiring option would be used?
**crossover cable
straight through cable
rollover cable
V.35 cable
16
What makes fiber preferable to copper cabling for interconnecting buildings? (Choose three.)
**greater distances per cable run
lower installation cost
xlimited susceptibility to EMI/RFI
durable connections
xgreater bandwidth potential
easily terminated
17
Refer to the exhibit. A network technician has been allocated the 192.168.1.0/24 private IP address range for use in the network that shown in the exhibit. Which subnet mask would be used to meet the host requirements for segment A of this internetwork?
**255.255.255.128
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
18
Which subnet mask would be assigned to the network address of 192.168.32.0 to provide 254 useable host addresses per subnetwork?
255.255.0.0
**255.255.255.0
255.255.254.0
255.255.248.0
19
What type of network cable is used between a terminal and a console port?
cross-over
straight-through
**rollover
patch cable
20
Which option identifies the primary interface which would be used for initial configuration of a Cisco router?
AUX interface
Ethernet interface
serial interface
**console interface
21
What are three common methods for setting a UTP Ethernet port to MDI or MDIX operation? (Choose three.)
direct configuration of the device
**cable color code association
cable selection and configuration
use of cable testers to determine pinouts
**the enabling of the mechanism to electrically swap the transmit and receive pairs
**the automatic detection and negotiating of MDI/MDIX operation of the port
22
Which device is used to create or divide broadcast domains?
hub
switch
bridge
**router
repeater
23
Refer to the exhibit. Assume that all devices are using default settings. How many subnets are required to address the topology that is shown?
1
3
4
**5
7
1
Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)
connecting a PC to a router's console port
**connecting two routers together via their fast ethernet ports
**connecting two switches together at gigabit speeds
connecting a PC to a switch at Gigabit Ethernet speeds
connecting two devices with the same interface type at Fast Ethernet speeds
2
Which three statements are true about the role of routers in the network? (Choose three.)
They propagate broadcasts.
They enlarge collision domains.
They segment broadcast domains.
**They interconnect different network technologies.
**Each router interface requires a separate network or subnet.
**They maintain a common frame format between LAN and WAN interfaces.
3
Refer to the exhibit. A network administrator has decided to use packet capture software to evaluate all traffic from the student subnet on the way to the Internet. To ensure that all packets are captured, what network device should be used to connect the monitoring station to the network between R1 and R2?
**router
hub
switch
wireless access point
4
A network administrator is required to use media in the network that can run up to 100 meters in cable length without using repeaters. The chosen media must be inexpensive and easily installed. The installation will be in a pre-existing building with limited cabling space. Which type of media would best meet these requirements?
STP
**UTP
coaxial
single-mode fiber
multimode fiber
5
Refer to the exhibit. Which three statements are true about the exhibited topology? (Choose three.)
Hosts B and C are in the same subnet.
**Five broadcast domains are present.
**Host B is using a crossover cable to connect to the router.
Four broadcast domains are present.
xFive networks are shown.
Host B is using a rollover cable to connect to the router.
6
Which three types of connectors are commonly associated with Cisco's V.35 serial cables? (Choose three.)
RJ 11
**DB 60
**Winchester 15 pin
DB 9
**smart serial
RJ 45
7
How many host addresses may be assigned on each subnetwork when using the 130.68.0.0 network address with a subnet mask of 255.255.248.0?
30
256
**2046
2048
4094
4096
8
Refer to the exhibit. Based on the IP configuration shown, what would be the result of Host A and Host B attempting to communicate outside the network segment?
both host A and B would be successful
**host A would be successful, host B would fail
host B would be successful, host A would fail
both Host A and B would fail
9
Refer to the exhibit. What destination IP address will PC1 place in the header for a packet destined for PC2?
192.168.1.1
192.168.2.1
192.168.2.2
192.168.3.1
**192.168.3.54
10
Refer to the exhibit. Which three statements identify the type of cabling that would be used in the segments that are shown? (Choose three.)
Segment 1 uses backbone cabling.
**Segment 1 uses a patch cable.
Segment 3 uses patch cabling.
Segment 3 uses vertical cabling.
**Segment 3 uses horizontal cabling.
**Segment 4 uses vertical cabling.
11
A company is planning to subnet its network for a maximum of 27 hosts. Which subnet mask would provide the needed hosts and leave the fewest unused addresses in each subnet?
255.255.255.0
255.255.255.192
**255.255.255.224
255.255.255.240
255.255.255.248
12
Refer to the exhibit. A student is setting up a home network primarily used for extensive file transfers, streaming video, and gaming. Which network device is best suited to these types of activities in the topology shown?
wireless access point
router
hub
**switch
13
Refer to the exhibit. How many subnets are required to support the network that is shown?
2
**3
4
5
14
What does the term "attenuation" mean in data communication?
**loss of signal strength as distance increases
time for a signal to reach its destination
leakage of signals from one cable pair to another
strengthening of a signal by a networking device
15
To establish a console connection from a computer to a Cisco router, which cable wiring option would be used?
**crossover cable
straight through cable
rollover cable
V.35 cable
16
What makes fiber preferable to copper cabling for interconnecting buildings? (Choose three.)
**greater distances per cable run
lower installation cost
xlimited susceptibility to EMI/RFI
durable connections
xgreater bandwidth potential
easily terminated
17
Refer to the exhibit. A network technician has been allocated the 192.168.1.0/24 private IP address range for use in the network that shown in the exhibit. Which subnet mask would be used to meet the host requirements for segment A of this internetwork?
**255.255.255.128
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
18
Which subnet mask would be assigned to the network address of 192.168.32.0 to provide 254 useable host addresses per subnetwork?
255.255.0.0
**255.255.255.0
255.255.254.0
255.255.248.0
19
What type of network cable is used between a terminal and a console port?
cross-over
straight-through
**rollover
patch cable
20
Which option identifies the primary interface which would be used for initial configuration of a Cisco router?
AUX interface
Ethernet interface
serial interface
**console interface
21
What are three common methods for setting a UTP Ethernet port to MDI or MDIX operation? (Choose three.)
direct configuration of the device
**cable color code association
cable selection and configuration
use of cable testers to determine pinouts
**the enabling of the mechanism to electrically swap the transmit and receive pairs
**the automatic detection and negotiating of MDI/MDIX operation of the port
22
Which device is used to create or divide broadcast domains?
hub
switch
bridge
**router
repeater
23
Refer to the exhibit. Assume that all devices are using default settings. How many subnets are required to address the topology that is shown?
1
3
4
**5
7
CCNA 1 - Module 9 Exam Answers
CHAPTER 9
1
In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet frame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do?
Host B can transmit immediately since it is connected on its own cable segment.
Host B must wait to receive a CSMA transmission from the hub, to signal its turn.
Host B must send a request signal to Host A by transmitting an interframe gap.
**Host B must wait until it is certain that Host A has completed sending its frame.
2 Ethernet operates at which layers of the OSI model? (Choose two.)
Network layer
Transport layer
**Physical layer
Application layer
Session layer
**Data-link layer
3 Which of the following describe interframe spacing? (Choose two.)
**the minimum interval, measured in bit-times, that any station must wait before sending another frame
the maximum interval, measured in bit-times, that any station must wait before sending another frame
the 96-bit payload padding inserted into a frame to achieve a legal frame size
the 96-bit frame padding transmitted between frames to achieve proper synchronization
**the time allowed for slow stations to process a frame and prepare for the next frame
the maximum interval within which a station must send another frame to avoid being considered unreachable
4 What three primary functions does data link layer encapsulation provide? (Choose three.)
**addressing
**error detection
**frame delimiting
port identification
path determination
IP address resolution
5 When a collision occurs in a network using CSMA/CD, how do hosts with data to transmit respond after the backoff period has expired?
**The hosts return to a listen-before-transmit mode. <---
The hosts creating the collision have priority to send data.
The hosts creating the collision retransmit the last 16 frames.
The hosts extend their delay period to allow for rapid transmission.
6 What are three functions of the upper data link sublayer in the OSI model? (Choose three.)
recognizes streams of bits
**identifies the network layer protocol
**makes the connection with the upper layers
identifies the source and destination applications
**insulates network layer protocols from changes in physical equipment
determines the source of a transmission when multiple devices are transmitting
7 What does the IEEE 802.2 standard represent in Ethernet technologies?
MAC sublayer
Physical layer
**Logical Link Control sublayer
Network layer
8 Why do hosts on an Ethernet segment that experience a collision use a random delay before attempting to transmit a frame?
A random delay is used to ensure a collision-free link.
A random delay value for each device is assigned by the manufacturer.
A standard delay value could not be agreed upon among networking device vendors.
**A random delay helps prevent the stations from experiencing another collision during the transmission.
9
Refer to the exhibit. Which option correctly matches the frame field type with the contents that frame field includes?
**header field - preamble and stop frame
data field - network layer packet
data field - physical addressing
trailer field - FCS and SoF
10 Host A has an IP address of 172.16.225.93 and a mask of 255.255.248.0. Host A needs to communicate with a new host whose IP is 172.16.231.78. Host A performs the ANDing operation on the destination address. What two things will occur? (Choose two.)
Host A will change the destination IP to the IP of the nearest router and forward the packet.
Host A will broadcast an ARP request for the MAC of its default gateway.
A result of 172.16.225.0 will be obtained.
**Host A will broadcast an ARP request for the MAC of the destination host.
A result of 172.16.224.0 will be obtained.
**A result of 172.16.225.255 will be obtained.
11 Which of the following is a drawback of the CSMA/CD access method?
**Collisions can decrease network performance.
It is more complex than non-deterministic protocols.
Deterministic media access protocols slow network performance.
CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies.
12 Ethernet operates at which layer of the TCP/IP network model?
application
physical
transport
internet
data link
**network access
13 What is the primary purpose of ARP?
translate URLs to IP addresses
**resolve IPv4 addresses to MAC addresses
provide dynamic IP configuration to network devices
convert internal private addresses to external public addresses
14
Refer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link?
**No collisions will occur on this link.
Only one of the devices can transmit at a time.
The switch will have priority for transmitting data.
The devices will default back to half duplex if excessive collisions occur.
15
Refer to the exhibit. Host_A is attempting to contact Server_B. Which statements correctly describe the addressing Host_A will generate in the process? (Choose two.)
A packet with the destination IP of Router_B.
A frame with the destination MAC address of Switch_A.
A packet with the destination IP of Router_A.
**A frame with the destination MAC address of Router_A.
**A packet with the destination IP of Server_B.
A frame with the destination MAC address of Server_B.
16 Which statements correctly describe MAC addresses? (Choose three.)
dynamically assigned
**copied into RAM during system startup
layer 3 address
**contains a 3 byte OUI
**6 bytes long
32 bits long
17 Which two features make switches preferable to hubs in Ethernet-based networks? (Choose two.)
reduction in cross-talk
**minimizing of collisions
support for UTP cabling
**division into broadcast domains
increase in the throughput of communications
18 What are the two most commonly used media types in Ethernet networks today? (Choose two.)
**coaxial thicknet
copper UTP
coaxial thinnet
optical fiber
**shielded twisted pair
19 Convert the binary number 10111010 into its hexadecimal equivalent. Select the correct answer from the list below.
85
90
**BA
A1
B3
1C
20 After an Ethernet collision, when the backoff algorithm is invoked, which device has priority to transmit data?
the device involved in the collision with the lowest MAC address
the device involved in the collision with the lowest IP address
**any device in the collision domain whose backoff timer expires first
those that began transmitting at the same time
1
In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet frame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do?
Host B can transmit immediately since it is connected on its own cable segment.
Host B must wait to receive a CSMA transmission from the hub, to signal its turn.
Host B must send a request signal to Host A by transmitting an interframe gap.
**Host B must wait until it is certain that Host A has completed sending its frame.
2 Ethernet operates at which layers of the OSI model? (Choose two.)
Network layer
Transport layer
**Physical layer
Application layer
Session layer
**Data-link layer
3 Which of the following describe interframe spacing? (Choose two.)
**the minimum interval, measured in bit-times, that any station must wait before sending another frame
the maximum interval, measured in bit-times, that any station must wait before sending another frame
the 96-bit payload padding inserted into a frame to achieve a legal frame size
the 96-bit frame padding transmitted between frames to achieve proper synchronization
**the time allowed for slow stations to process a frame and prepare for the next frame
the maximum interval within which a station must send another frame to avoid being considered unreachable
4 What three primary functions does data link layer encapsulation provide? (Choose three.)
**addressing
**error detection
**frame delimiting
port identification
path determination
IP address resolution
5 When a collision occurs in a network using CSMA/CD, how do hosts with data to transmit respond after the backoff period has expired?
**The hosts return to a listen-before-transmit mode. <---
The hosts creating the collision have priority to send data.
The hosts creating the collision retransmit the last 16 frames.
The hosts extend their delay period to allow for rapid transmission.
6 What are three functions of the upper data link sublayer in the OSI model? (Choose three.)
recognizes streams of bits
**identifies the network layer protocol
**makes the connection with the upper layers
identifies the source and destination applications
**insulates network layer protocols from changes in physical equipment
determines the source of a transmission when multiple devices are transmitting
7 What does the IEEE 802.2 standard represent in Ethernet technologies?
MAC sublayer
Physical layer
**Logical Link Control sublayer
Network layer
8 Why do hosts on an Ethernet segment that experience a collision use a random delay before attempting to transmit a frame?
A random delay is used to ensure a collision-free link.
A random delay value for each device is assigned by the manufacturer.
A standard delay value could not be agreed upon among networking device vendors.
**A random delay helps prevent the stations from experiencing another collision during the transmission.
9
Refer to the exhibit. Which option correctly matches the frame field type with the contents that frame field includes?
**header field - preamble and stop frame
data field - network layer packet
data field - physical addressing
trailer field - FCS and SoF
10 Host A has an IP address of 172.16.225.93 and a mask of 255.255.248.0. Host A needs to communicate with a new host whose IP is 172.16.231.78. Host A performs the ANDing operation on the destination address. What two things will occur? (Choose two.)
Host A will change the destination IP to the IP of the nearest router and forward the packet.
Host A will broadcast an ARP request for the MAC of its default gateway.
A result of 172.16.225.0 will be obtained.
**Host A will broadcast an ARP request for the MAC of the destination host.
A result of 172.16.224.0 will be obtained.
**A result of 172.16.225.255 will be obtained.
11 Which of the following is a drawback of the CSMA/CD access method?
**Collisions can decrease network performance.
It is more complex than non-deterministic protocols.
Deterministic media access protocols slow network performance.
CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies.
12 Ethernet operates at which layer of the TCP/IP network model?
application
physical
transport
internet
data link
**network access
13 What is the primary purpose of ARP?
translate URLs to IP addresses
**resolve IPv4 addresses to MAC addresses
provide dynamic IP configuration to network devices
convert internal private addresses to external public addresses
14
Refer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link?
**No collisions will occur on this link.
Only one of the devices can transmit at a time.
The switch will have priority for transmitting data.
The devices will default back to half duplex if excessive collisions occur.
15
Refer to the exhibit. Host_A is attempting to contact Server_B. Which statements correctly describe the addressing Host_A will generate in the process? (Choose two.)
A packet with the destination IP of Router_B.
A frame with the destination MAC address of Switch_A.
A packet with the destination IP of Router_A.
**A frame with the destination MAC address of Router_A.
**A packet with the destination IP of Server_B.
A frame with the destination MAC address of Server_B.
16 Which statements correctly describe MAC addresses? (Choose three.)
dynamically assigned
**copied into RAM during system startup
layer 3 address
**contains a 3 byte OUI
**6 bytes long
32 bits long
17 Which two features make switches preferable to hubs in Ethernet-based networks? (Choose two.)
reduction in cross-talk
**minimizing of collisions
support for UTP cabling
**division into broadcast domains
increase in the throughput of communications
18 What are the two most commonly used media types in Ethernet networks today? (Choose two.)
**coaxial thicknet
copper UTP
coaxial thinnet
optical fiber
**shielded twisted pair
19 Convert the binary number 10111010 into its hexadecimal equivalent. Select the correct answer from the list below.
85
90
**BA
A1
B3
1C
20 After an Ethernet collision, when the backoff algorithm is invoked, which device has priority to transmit data?
the device involved in the collision with the lowest MAC address
the device involved in the collision with the lowest IP address
**any device in the collision domain whose backoff timer expires first
those that began transmitting at the same time
CCNA 1 - Module 8 Exam Answers
CHAPTER 8
1
Which type of cable run is most often associated with fiber-optic cable?
Xbackbone cable
horizontal cable
patch cable
work area cable
2
In most business LANs, which connector is used with twisted-pair networking cable?
BNC
RJ-11
**RJ-45
Type F
3
When is a straight-through cable used in a network?
when connecting a router through the console port
when connecting one switch to another switch
**when connecting a host to a switch
when connecting a router to another router
4
With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
**the magnetic field around the adjacent pairs of wire
the use of braided wire to shield the adjacent wire pairs
the reflection of the electrical wave back from the far end of the cable
the collision caused by two nodes trying to use the media simultaneously
5
Which OSI layer is responsible for binary transmission, cable specification, and physical aspects of network communication?
Presentation
Transport
Data Link
**Physical
6
An installed fiber run can be checked for faults, integrity, and the performance of the media by using what device?
light injector
**OTDR
TDR
multimeter
7
XYZ Company is installing new cable runs on their data network. What two types of cable would most commonly be used for new runs? (Choose two.)
**coax
Cat4 UTP
Cat5 UTP
**Cat6 UTP
STP
8
What is a possible effect of improperly applying a connector to a network cable?
Data will be forwarded to the wrong node.
**Data transmitted through that cable may experience signal loss.
An improper signaling method will be implemented for data transmitted on that cable.
The encoding method for data sent on that cable will change to compensate for the improper connection.
9
What are three measures of data transfer? (Choose three.)
goodput
**frequency
amplitude
**throughput
crosstalk
**bandwidth
10
Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?
coax cable
rollover cable
**crossover cable
straight-through cable
11
In LAN installations where potential electrical hazards or electromagnetic interference may be present, what type of media is recommended for backbone cabling?
coax
**fiber
Cat5e UTP
Cat6 UTP
STP
12
Which fiber connector supports full duplex Ethernet?
kolmas
13
Which method of signal transmission uses radio waves to carry signals?
electrical
optical
**wireless
acoustic
14
Which characteristics describe fiber optic cable? (Choose two.)
**It is not affected by EMI or RFI.
Each pair of cables is wrapped in metallic foil.
It combines the technique of cancellation, shielding and twisting to protect data.
It has a maximum speed of 100 Mbps.
**It is the most expensive type of LAN cabling.
15
Which of the following is a characteristic of single-mode fiber-optic cable?
**generally uses LEDs as the light source
relatively larger core with multiple light paths
less expensive than multimode
generally uses lasers as the light source
16
What is considered a benefit of wireless as a media choice?
**more host mobility
lower security risks
reduced susceptibility to interference
less impact of the surroundings on the effective coverage area
17
What characteristic of UTP cable helps reduce the effects of interference?
the metal braiding in the shielding
the reflective cladding around core
**the twisting of the wires in the cable
the insulating material in the outer jacket
18
What is a primary role of the Physical layer in transmitting data on the network?
**create the signals that represent the bits in each frame on to the media
provide physical addressing to the devices
determine the path packets take through the network
control data access to the media
1
Which type of cable run is most often associated with fiber-optic cable?
Xbackbone cable
horizontal cable
patch cable
work area cable
2
In most business LANs, which connector is used with twisted-pair networking cable?
BNC
RJ-11
**RJ-45
Type F
3
When is a straight-through cable used in a network?
when connecting a router through the console port
when connecting one switch to another switch
**when connecting a host to a switch
when connecting a router to another router
4
With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
**the magnetic field around the adjacent pairs of wire
the use of braided wire to shield the adjacent wire pairs
the reflection of the electrical wave back from the far end of the cable
the collision caused by two nodes trying to use the media simultaneously
5
Which OSI layer is responsible for binary transmission, cable specification, and physical aspects of network communication?
Presentation
Transport
Data Link
**Physical
6
An installed fiber run can be checked for faults, integrity, and the performance of the media by using what device?
light injector
**OTDR
TDR
multimeter
7
XYZ Company is installing new cable runs on their data network. What two types of cable would most commonly be used for new runs? (Choose two.)
**coax
Cat4 UTP
Cat5 UTP
**Cat6 UTP
STP
8
What is a possible effect of improperly applying a connector to a network cable?
Data will be forwarded to the wrong node.
**Data transmitted through that cable may experience signal loss.
An improper signaling method will be implemented for data transmitted on that cable.
The encoding method for data sent on that cable will change to compensate for the improper connection.
9
What are three measures of data transfer? (Choose three.)
goodput
**frequency
amplitude
**throughput
crosstalk
**bandwidth
10
Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?
coax cable
rollover cable
**crossover cable
straight-through cable
11
In LAN installations where potential electrical hazards or electromagnetic interference may be present, what type of media is recommended for backbone cabling?
coax
**fiber
Cat5e UTP
Cat6 UTP
STP
12
Which fiber connector supports full duplex Ethernet?
kolmas
13
Which method of signal transmission uses radio waves to carry signals?
electrical
optical
**wireless
acoustic
14
Which characteristics describe fiber optic cable? (Choose two.)
**It is not affected by EMI or RFI.
Each pair of cables is wrapped in metallic foil.
It combines the technique of cancellation, shielding and twisting to protect data.
It has a maximum speed of 100 Mbps.
**It is the most expensive type of LAN cabling.
15
Which of the following is a characteristic of single-mode fiber-optic cable?
**generally uses LEDs as the light source
relatively larger core with multiple light paths
less expensive than multimode
generally uses lasers as the light source
16
What is considered a benefit of wireless as a media choice?
**more host mobility
lower security risks
reduced susceptibility to interference
less impact of the surroundings on the effective coverage area
17
What characteristic of UTP cable helps reduce the effects of interference?
the metal braiding in the shielding
the reflective cladding around core
**the twisting of the wires in the cable
the insulating material in the outer jacket
18
What is a primary role of the Physical layer in transmitting data on the network?
**create the signals that represent the bits in each frame on to the media
provide physical addressing to the devices
determine the path packets take through the network
control data access to the media
CCNA 1 - Module 7 Exam Answers
CHAPTER 7
1
Which options are properties of contention-based media access for a shared media? (Choose three.)
**non-deterministic
**less overhead
one station transmits at a time
**collisions exist
devices must wait their turn
token passing
2
What is a primary purpose of encapsulating packets into frames?
provide routes across the internetwork
format the data for presentation to the user
**facilitate the entry and exit of data on media
identify the services to which transported data is associated
3
Refer to the exhibit. How many unique CRC calculations will take place as traffic routes from the PC to the laptop?
1
**2
4
8
4
What is true concerning physical and logical topologies?
The logical topology is always the same as the physical topology.
Physical topologies are concerned with how a network transfers frames.
Physical signal paths are defined by Data Link layer protocols.
**Logical topologies consist of virtual connections between nodes.
5
Refer to the exhibit. Assuming that the network in the exhibit is converged meaning the routing tables and ARP tables are complete, which MAC address will Host A place in the destination address field of Ethernet frames destined for www.server?
00-1c-41-ab-c0-00
**00-0c-85-cf-65-c0
00-0c-85-cf-65-c1
00-12-3f-32-05-af
6
What are three characteristics of valid Ethernet Layer 2 addresses? (Choose three.)
**They are 48 binary bits in length.
They are considered physical addresses.
**They are generally represented in hexadecimal format.
They consist of four eight-bit octets of binary numbers.
They are used to determine the data path through the network.
**They must be changed when an Ethernet device is added or moved within the network.
7
Refer to the exhibit. A frame is being sent from the PC to the laptop. Which source MAC and IP addresses will be included in the frame as it leaves RouterB? (Choose two.)
source MAC - PC
source MAC - S0/0 on RouterA
**source MAC - Fa0/1 on RouterB
**source IP - PC
source IP - S0/0 on RouterA
source IP - Fa0/1 of RouterB
8
What determines the method of media access control? (Choose two.)
network layer addressing
**media sharing
application processes
**logical topology
intermediary device function
9
What is the purpose of the preamble in an Ethernet frame?
is used as a pad for data
identifies the source address
identifies the destination address
marks the end of timing information
**is used for timing synchronization with alternating patterns of ones and zeros
10
What statements are true regarding addresses found at each layer of the OSI model? (Choose two.)
**Layer 2 may identify devices by a physical address burned into the network card
Layer 2 identifies the applications that are communicating
**Layer 3 represents a hierarchical addressing scheme
Layer 4 directs communication to the proper destination network
Layer 4 addresses are used by intermediary devices to forward data
11
Which statements describe the logical token-passing topology? (Choose two.)
Network usage is on a first come, first serve basis.
**Computers are allowed to transmit data only when they possess a token.
Data from a host is received by all other hosts.
**Electronic tokens are passed sequentially to each other.
Token passing networks have problems with high collision rates.
12
Which sublayer of the data link layer prepares a signal to be transmitted at the physical layer?
LLC
**MAC
HDLC
NIC
13
What is true regarding media access control? (Choose three.)
**Ethernet utilizes CSMA/CD
**defined as placement of data frames on the media
contention-based access is also known as deterministic
802.11 utilizes CSMA/CD
**Data Link layer protocols define the rules for access to different media
controlled access contains data collisions
14
What is a characteristic of a logical point-to-point topology?
The nodes are physically connected.
The physical arrangement of the nodes is restricted.
**The media access control protocol can be very simple.
The data link layer protocol used over the link requires a large frame header.
15
What two facts are true when a device is moved from one network or subnet to another? (Choose two.)
The Layer 2 address must be reassigned.
The default gateway address should not be changed.
**The device will still operate at the same Layer 2 address.
Applications and services will need additional port numbers assigned.
**The Layer 3 address must be reassigned to allow communications to the new network.
16
What is a function of the data link layer?
provides the formatting of data
provides end-to-end delivery of data between hosts
provides delivery of data between two applications
**provides for the exchange data over a common local media
17
Which three factors should be considered when implementing a Layer 2 protocol in a network? (Choose three.)
the Layer 3 protocol selected
**the geographic scope of the network
the PDU defined by the transport layer
**the physical layer implementation
**the number of hosts to be interconnected
18
What is the primary purpose of the trailer in a data link layer frame?
define the logical topology
provide media access control
**support frame error detection
carry routing information for the frame
19
A network administrator has been asked to provide a graphic representation of exactly where the company network wiring and equipment are located in the building. What is this type of drawing?
logical topology
**physical topology
cable path
wiring grid
access topology
20
Refer to the exhibit. Which statement describes the media access control methods that are used by the networks in the exhibit?
All three networks use CSMA/CA
None of the networks require media access control.
**Network 1 uses CSMA/CD and Network 3 uses CSMA/CA.
Network 1 uses CSMA/CA and Network 2 uses CSMA/CD.
Network 2 uses CSMA/CA and Network 3 uses CSMA/CD.
1
Which options are properties of contention-based media access for a shared media? (Choose three.)
**non-deterministic
**less overhead
one station transmits at a time
**collisions exist
devices must wait their turn
token passing
2
What is a primary purpose of encapsulating packets into frames?
provide routes across the internetwork
format the data for presentation to the user
**facilitate the entry and exit of data on media
identify the services to which transported data is associated
3
Refer to the exhibit. How many unique CRC calculations will take place as traffic routes from the PC to the laptop?
1
**2
4
8
4
What is true concerning physical and logical topologies?
The logical topology is always the same as the physical topology.
Physical topologies are concerned with how a network transfers frames.
Physical signal paths are defined by Data Link layer protocols.
**Logical topologies consist of virtual connections between nodes.
5
Refer to the exhibit. Assuming that the network in the exhibit is converged meaning the routing tables and ARP tables are complete, which MAC address will Host A place in the destination address field of Ethernet frames destined for www.server?
00-1c-41-ab-c0-00
**00-0c-85-cf-65-c0
00-0c-85-cf-65-c1
00-12-3f-32-05-af
6
What are three characteristics of valid Ethernet Layer 2 addresses? (Choose three.)
**They are 48 binary bits in length.
They are considered physical addresses.
**They are generally represented in hexadecimal format.
They consist of four eight-bit octets of binary numbers.
They are used to determine the data path through the network.
**They must be changed when an Ethernet device is added or moved within the network.
7
Refer to the exhibit. A frame is being sent from the PC to the laptop. Which source MAC and IP addresses will be included in the frame as it leaves RouterB? (Choose two.)
source MAC - PC
source MAC - S0/0 on RouterA
**source MAC - Fa0/1 on RouterB
**source IP - PC
source IP - S0/0 on RouterA
source IP - Fa0/1 of RouterB
8
What determines the method of media access control? (Choose two.)
network layer addressing
**media sharing
application processes
**logical topology
intermediary device function
9
What is the purpose of the preamble in an Ethernet frame?
is used as a pad for data
identifies the source address
identifies the destination address
marks the end of timing information
**is used for timing synchronization with alternating patterns of ones and zeros
10
What statements are true regarding addresses found at each layer of the OSI model? (Choose two.)
**Layer 2 may identify devices by a physical address burned into the network card
Layer 2 identifies the applications that are communicating
**Layer 3 represents a hierarchical addressing scheme
Layer 4 directs communication to the proper destination network
Layer 4 addresses are used by intermediary devices to forward data
11
Which statements describe the logical token-passing topology? (Choose two.)
Network usage is on a first come, first serve basis.
**Computers are allowed to transmit data only when they possess a token.
Data from a host is received by all other hosts.
**Electronic tokens are passed sequentially to each other.
Token passing networks have problems with high collision rates.
12
Which sublayer of the data link layer prepares a signal to be transmitted at the physical layer?
LLC
**MAC
HDLC
NIC
13
What is true regarding media access control? (Choose three.)
**Ethernet utilizes CSMA/CD
**defined as placement of data frames on the media
contention-based access is also known as deterministic
802.11 utilizes CSMA/CD
**Data Link layer protocols define the rules for access to different media
controlled access contains data collisions
14
What is a characteristic of a logical point-to-point topology?
The nodes are physically connected.
The physical arrangement of the nodes is restricted.
**The media access control protocol can be very simple.
The data link layer protocol used over the link requires a large frame header.
15
What two facts are true when a device is moved from one network or subnet to another? (Choose two.)
The Layer 2 address must be reassigned.
The default gateway address should not be changed.
**The device will still operate at the same Layer 2 address.
Applications and services will need additional port numbers assigned.
**The Layer 3 address must be reassigned to allow communications to the new network.
16
What is a function of the data link layer?
provides the formatting of data
provides end-to-end delivery of data between hosts
provides delivery of data between two applications
**provides for the exchange data over a common local media
17
Which three factors should be considered when implementing a Layer 2 protocol in a network? (Choose three.)
the Layer 3 protocol selected
**the geographic scope of the network
the PDU defined by the transport layer
**the physical layer implementation
**the number of hosts to be interconnected
18
What is the primary purpose of the trailer in a data link layer frame?
define the logical topology
provide media access control
**support frame error detection
carry routing information for the frame
19
A network administrator has been asked to provide a graphic representation of exactly where the company network wiring and equipment are located in the building. What is this type of drawing?
logical topology
**physical topology
cable path
wiring grid
access topology
20
Refer to the exhibit. Which statement describes the media access control methods that are used by the networks in the exhibit?
All three networks use CSMA/CA
None of the networks require media access control.
**Network 1 uses CSMA/CD and Network 3 uses CSMA/CA.
Network 1 uses CSMA/CA and Network 2 uses CSMA/CD.
Network 2 uses CSMA/CA and Network 3 uses CSMA/CD.
CCNA 1 - Module 6 Exam Answers
CHAPTER 6
1
How many bits make up an IPv4 address?
128
64
48
32 **
2
Refer to the exhibit. A network administrator has to develop an IP addressing scheme that uses the 192.168.1.0 /24 address space. The network that contains the serial link has already been addressed out of a separate range. Each network will be allocated the same number of host addresses. Which network mask will be appropriate to address the remaining networks?
255.255.255.248
255.255.255.224
255.255.255.192 **
255.255.255.240
255.255.255.128
255.255.255.252
3
Refer to the exhibit. The network administrator has assigned the internetwork of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 mask. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new network (subnet zero is the first subnet). By company policies, the router interface is always assigned the first usable host address and the workgroup server is given the last usable host address. Which configuration should be entered into the workgroup server's properties to allow connectivity to the network?
IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.39
IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.33
IP address: 192.168.10.38 subnet mask: 255.255.255.248 default gateway: 192.168.10.33 **
IP address: 192.168.10.39 subnet mask: 255.255.255.248 default gateway: 192.168.10.31
IP address: 192.168.10.254 subnet mask: 255.255.255.0 default gateway: 192.168.10.1
4
Refer to the exhibit. Which network prefix will work with the IP addressing scheme shown in the graphic.
/24
/16
/20
/27 **
/25
/28
5
Refer to the exhibit. A network administrator discovers that host A is having trouble with Internet connectivity, but the server farm has full connectivity. In addition, host A has full connectivity to the server farm. What is a possible cause of this problem?
The router has an incorrect gateway.
Host A has an overlapping network address.
Host A has an incorrect default gateway configured.
Host A has an incorrect subnet mask.
NAT is required for the host A network. **
6
What subnet mask would a network administrator assign to a network address of 172.30.1.0 if it were possible to have up to 254 hosts?
255.255.0.0
255.255.255.0 **
255.255.254.0
255.255.248.0
7
Given the IP address and subnet mask of 172.16.134.64 255.255.255.224, which of the following would describe this address?
This is a useable host address.
This is a broadcast address.
This is a network address. **
This is not a valid address.
8
What three facts are true about the network portion of an IPv4 address? (Choose three.)
identifies an individual device
is identical for all hosts in a broadcast domain
is altered as packet is forwarded **
varies in length **
is used to forward packets **
uses flat addressing
9
What is the network address of the host 172.25.67.99 /23 in binary?
10101100. 00011001.01000011.00000000
10101100. 00011001.01000011.11111111
10101100. 00011001.01000010.00000000 **
10101100. 00011001.01000010.01100011
10101100. 00010001.01000011. 01100010
10101100. 00011001.00000000.00000000
10
A router interface has been assigned an IP address of 172.16.192.166 with a mask of 255.255.255.248. To which subnet does the IP address belong?
172.16.0.0
172.16.192.0
172.16.192.128
172.16.192.160 **
172.16.192.168
172.16.192.176
11
Refer to the exhibit. Why would the response shown be displayed after issuing the command ping 127.0.0.1 on a PC?
The IP settings are not properly configured on the host. **
Internet Protocol is not properly installed on the host.
There is a problem at the physical or data link layer.
The default gateway device is not operating.
A router on the path to the destination host has gone down.
12
What two things will happen if a router receives an ICMP packet which has a TTL value of 1 and the destination host is several hops away? (Choose two.)
The router will discard the packet.
The router will decrement the TTL value and forward the packet to the next router on the path to the destination host.
The router will send a time exceeded message to the source host. **
The router will increment the TTL value and forward the packet to the next router on the path to the destination host.
The router will send an ICMP Redirect Message to the source host. **
13
Refer to the exhibit. An administrator is designing security rules for the 192.168.22.0 /24 network. Each security rule requires an address and mask pair to represent the machines that will be affected by the rule. Which two address and mask pairs will be the most precise way to reference the servers and hosts separately. (Choose two.)
192.168.22.40 255.255.255.248
192.168.22.40 255.255.255.252
192.168.22.100 255.255.255.128
192.168.22.100 255.255.255.254 **
192.168.22.1 255.255.255.192 **
192.168.22.101 255.255.255.224
14
Which of the following are features of IPv6? (Choose three.)
larger address space **
faster routing protocols
data types and classes of service **
authentication and encryption **
improved host naming conventions
same addressing scheme as IPv4
15
Which process do routers use to determine the subnet network address based upon a given IP address and subnet mask?
binary adding
hexadecimal anding
binary division
binary multiplication
binary ANDing **
16
What is the primary reason for development of IPv6?
security
header format simplification
expanded addressing capabilities **
addressing simplification
17
Which three IP addresses are private? (Choose three.)
172.168.33.1
10.35.66.70 **
192.168.99.5 **
172.18.88.90 **
192.33.55.89
172.35.16.5
18
Which statements are true regarding IP addressing? (Choose two.)
NAT translates public addresses to private addresses destined for the Internet.
Only one company is allowed to use a specific private network address space.
Private addresses are blocked from public Internet by router. **
Network 172.32.0.0 is part of the private address space.
IP address 127.0.0.1 can be used for a host to direct traffic to itself. **
19
Which IPv4 subnetted addresses represent valid host addresses? (Choose three.)
172.16.4.127 /26
172.16.4.155 /26 **
172.16.4.193 /26 **
172.16.4.95 /27
172.16.4.159 /27
172.16.4.207 /27 **
20
What is a group of hosts called that have identical bit patterns in the high order bits of their addresses?
an internet
a network **
an octet
a radi **
21
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?
The host subnet mask is incorrect.
The default gateway is a network address.
The default gateway is a broadcast address.
The default gateway is on a different subnet from the host. **
22
Which of the following network devices are recommended to be assigned static IP addresses? (Choose three.)
LAN workstations
servers **
network printers **
routers **
remote workstations
laptops
1
How many bits make up an IPv4 address?
128
64
48
32 **
2
Refer to the exhibit. A network administrator has to develop an IP addressing scheme that uses the 192.168.1.0 /24 address space. The network that contains the serial link has already been addressed out of a separate range. Each network will be allocated the same number of host addresses. Which network mask will be appropriate to address the remaining networks?
255.255.255.248
255.255.255.224
255.255.255.192 **
255.255.255.240
255.255.255.128
255.255.255.252
3
Refer to the exhibit. The network administrator has assigned the internetwork of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 mask. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new network (subnet zero is the first subnet). By company policies, the router interface is always assigned the first usable host address and the workgroup server is given the last usable host address. Which configuration should be entered into the workgroup server's properties to allow connectivity to the network?
IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.39
IP address: 192.168.10.38 subnet mask: 255.255.255.240 default gateway: 192.168.10.33
IP address: 192.168.10.38 subnet mask: 255.255.255.248 default gateway: 192.168.10.33 **
IP address: 192.168.10.39 subnet mask: 255.255.255.248 default gateway: 192.168.10.31
IP address: 192.168.10.254 subnet mask: 255.255.255.0 default gateway: 192.168.10.1
4
Refer to the exhibit. Which network prefix will work with the IP addressing scheme shown in the graphic.
/24
/16
/20
/27 **
/25
/28
5
Refer to the exhibit. A network administrator discovers that host A is having trouble with Internet connectivity, but the server farm has full connectivity. In addition, host A has full connectivity to the server farm. What is a possible cause of this problem?
The router has an incorrect gateway.
Host A has an overlapping network address.
Host A has an incorrect default gateway configured.
Host A has an incorrect subnet mask.
NAT is required for the host A network. **
6
What subnet mask would a network administrator assign to a network address of 172.30.1.0 if it were possible to have up to 254 hosts?
255.255.0.0
255.255.255.0 **
255.255.254.0
255.255.248.0
7
Given the IP address and subnet mask of 172.16.134.64 255.255.255.224, which of the following would describe this address?
This is a useable host address.
This is a broadcast address.
This is a network address. **
This is not a valid address.
8
What three facts are true about the network portion of an IPv4 address? (Choose three.)
identifies an individual device
is identical for all hosts in a broadcast domain
is altered as packet is forwarded **
varies in length **
is used to forward packets **
uses flat addressing
9
What is the network address of the host 172.25.67.99 /23 in binary?
10101100. 00011001.01000011.00000000
10101100. 00011001.01000011.11111111
10101100. 00011001.01000010.00000000 **
10101100. 00011001.01000010.01100011
10101100. 00010001.01000011. 01100010
10101100. 00011001.00000000.00000000
10
A router interface has been assigned an IP address of 172.16.192.166 with a mask of 255.255.255.248. To which subnet does the IP address belong?
172.16.0.0
172.16.192.0
172.16.192.128
172.16.192.160 **
172.16.192.168
172.16.192.176
11
Refer to the exhibit. Why would the response shown be displayed after issuing the command ping 127.0.0.1 on a PC?
The IP settings are not properly configured on the host. **
Internet Protocol is not properly installed on the host.
There is a problem at the physical or data link layer.
The default gateway device is not operating.
A router on the path to the destination host has gone down.
12
What two things will happen if a router receives an ICMP packet which has a TTL value of 1 and the destination host is several hops away? (Choose two.)
The router will discard the packet.
The router will decrement the TTL value and forward the packet to the next router on the path to the destination host.
The router will send a time exceeded message to the source host. **
The router will increment the TTL value and forward the packet to the next router on the path to the destination host.
The router will send an ICMP Redirect Message to the source host. **
13
Refer to the exhibit. An administrator is designing security rules for the 192.168.22.0 /24 network. Each security rule requires an address and mask pair to represent the machines that will be affected by the rule. Which two address and mask pairs will be the most precise way to reference the servers and hosts separately. (Choose two.)
192.168.22.40 255.255.255.248
192.168.22.40 255.255.255.252
192.168.22.100 255.255.255.128
192.168.22.100 255.255.255.254 **
192.168.22.1 255.255.255.192 **
192.168.22.101 255.255.255.224
14
Which of the following are features of IPv6? (Choose three.)
larger address space **
faster routing protocols
data types and classes of service **
authentication and encryption **
improved host naming conventions
same addressing scheme as IPv4
15
Which process do routers use to determine the subnet network address based upon a given IP address and subnet mask?
binary adding
hexadecimal anding
binary division
binary multiplication
binary ANDing **
16
What is the primary reason for development of IPv6?
security
header format simplification
expanded addressing capabilities **
addressing simplification
17
Which three IP addresses are private? (Choose three.)
172.168.33.1
10.35.66.70 **
192.168.99.5 **
172.18.88.90 **
192.33.55.89
172.35.16.5
18
Which statements are true regarding IP addressing? (Choose two.)
NAT translates public addresses to private addresses destined for the Internet.
Only one company is allowed to use a specific private network address space.
Private addresses are blocked from public Internet by router. **
Network 172.32.0.0 is part of the private address space.
IP address 127.0.0.1 can be used for a host to direct traffic to itself. **
19
Which IPv4 subnetted addresses represent valid host addresses? (Choose three.)
172.16.4.127 /26
172.16.4.155 /26 **
172.16.4.193 /26 **
172.16.4.95 /27
172.16.4.159 /27
172.16.4.207 /27 **
20
What is a group of hosts called that have identical bit patterns in the high order bits of their addresses?
an internet
a network **
an octet
a radi **
21
Refer to the exhibit. Host A is connected to the LAN, but it cannot get access to any resources on the Internet. The configuration of the host is shown in the exhibit. What could be the cause of the problem?
The host subnet mask is incorrect.
The default gateway is a network address.
The default gateway is a broadcast address.
The default gateway is on a different subnet from the host. **
22
Which of the following network devices are recommended to be assigned static IP addresses? (Choose three.)
LAN workstations
servers **
network printers **
routers **
remote workstations
laptops
CCNA 1 - Module 5 Exam Answers
CHAPTER 5
1
In an IPv4 environment, what information is used by the router to forward data packets from one interface of a router to another?
**destination network address
source network address
source MAC address
well known port destination address
2
What information is added during encapsulation at OSI Layer 3?
source and destination MAC
source and destination application protocol
source and destination port number
**source and destination IP address
3
In a connectionless system, which of the following is correct?
The destination is contacted before a packet is sent.
**The destination is not contacted before a packet is sent.
The destination sends an acknowledgement to the source that indicates the packet was received.
The destination sends an acknowledgement to the source that requests the next packet to be sent.
4
Which IP packet field will prevent endless loops?
type-of-service
identification
flags
**time-to-live
header checksum
5
Which portion of the network layer address does a router use to forward packets?
host portion
broadcast address
**network portion
gateway address
6
Refer to the exhibit. Using the network in the exhibit, what would be the default gateway address for host A in the 192.133.219.0 network?
192.135.250.1
192.31.7.1
192.133.219.0
**192.133.219.1
7
If the default gateway is configured incorrectly on the host, what is the impact on communications?
The host is unable to communicate on the local network.
**The host can communicate with other hosts on the local network, but is unable to communicate with hosts on remote networks.
The host can communicate with other hosts on remote networks, but is unable to communicate with hosts on the local network.
There is no impact on communications.
8
What is the purpose of a default gateway?
physically connects a computer to a network
provides a permanent address to a computer
identifies the network to which a computer is connected
identifies the logical address of a networked computer and uniquely identifies it to the rest of the network
**identifies the device that allows local network computers to communicate with devices on other networks
9
What type of routing uses information that is manually entered into the routing table?
dynamic
interior
**static
standard
10
When the destination network is not listed in the routing table of a Cisco router, what are two possible actions that the router might take? (Choose two.)
**The router sends an ARP request to determine the required next hop address.
The router discards the packet.
The router forwards the packet toward the next hop indicated in the ARP table.
**The router forwards the packet to the interface indicated by the source address.
The router forwards the packet out the interface indicated by the default route entry.
11
What are the key factors to consider when grouping hosts into a common network? (Choose three.)
**gateways
purpose
physical addressing
software version
**geographic location
**ownership
12
What is a component of a routing table entry?
the MAC address of the interface of the router
the destination Layer 4 port number
the destination host address
**the next-hop address
13
Which intermediary devices could be used to implement security between networks? (Choose two.)
**router
hub
switch
**firewall
access point
bridge
14
What are three common problems with a large network? (Choose three.)
too few broadcasts
**performance degradation
**security issues
**limited management responsibility
host identification
protocol compatibility
15
Refer to the exhibit. All devices shown in the exhibit have factory default settings. How many broadcast domains are represented in the topology that is shown?
3
**4
5
7
8
11
16
Which three statements are true about routes and their use? (Choose three.)
If no route to the destination network is found, the packet is returned to the previous router.
If the destination network is directly connected, the router forwards the packet to the destination host.
**If multiple network entries exist for the destination network, the most general route is used to forward the packet.
**If no route exists for the destination network and a default route is present, the packet is forwarded to the next-hop router.
**If the originating host has a default gateway configured, the packet for a remote network can be forwarded using that route.
If a host does not have a route manually configured for the destination network, the host will drop the packet.
17
Refer to the exhibit. A network administrator is troubleshooting a connectivity problem and needs to determine the address that is used to forward network packets out the network. Using the netstat -r command, the administrator would identify which address as the address to which all hosts send packets that are destined for an outside network?
10.10.10.26
127.0.0.1
**10.10.10.6
10.10.10.1
224.0.0.0
18
Refer to the exhibit. A network administrator notices that there are too many broadcasts on the network. What two steps can the network administrator take to resolve this problem? (Choose two.)
**Replace S2 with a router.
Place all servers on S1.
Disable TCP/IP broadcasts.
**Subnet the 192.168.0.0 /24 network.
Disable all unused interfaces on the switches.
19
Refer to the exhibit. The network in the exhibit is fully operational. What two statements correctly describe the routing for the topology that is shown? (Choose two.)
**192.168.0.2 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 network to the 172.16.0.0 network.
10.0.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 10.0.0.0 network.
**192.168.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 172.16.0.0 network.
172.16.0.1 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 to the 172.16.0.0 network.
192.168.0.1 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
192.168.0.2 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
20
What two characteristics are commonly associated with dynamic routing protocols? (Choose two.)
require no device configuration
**provide routers with up-to-date routing tables
require less processing power than static routes require
consume bandwidth to exchange route information
**prevent manual configuration and maintenance of the routing table
21
What statement describes the purpose of a default route?
A host uses a default route to transfer data to another host on the same network segment.
A host uses a default route to forward data to the local switch as the next hop to all destinations.
A host uses a default route to identify the Layer 2 address of an end device on the local network.
**A host uses a default route to transfer data to a host outside the local network when no other route to the destination exists.
1
In an IPv4 environment, what information is used by the router to forward data packets from one interface of a router to another?
**destination network address
source network address
source MAC address
well known port destination address
2
What information is added during encapsulation at OSI Layer 3?
source and destination MAC
source and destination application protocol
source and destination port number
**source and destination IP address
3
In a connectionless system, which of the following is correct?
The destination is contacted before a packet is sent.
**The destination is not contacted before a packet is sent.
The destination sends an acknowledgement to the source that indicates the packet was received.
The destination sends an acknowledgement to the source that requests the next packet to be sent.
4
Which IP packet field will prevent endless loops?
type-of-service
identification
flags
**time-to-live
header checksum
5
Which portion of the network layer address does a router use to forward packets?
host portion
broadcast address
**network portion
gateway address
6
Refer to the exhibit. Using the network in the exhibit, what would be the default gateway address for host A in the 192.133.219.0 network?
192.135.250.1
192.31.7.1
192.133.219.0
**192.133.219.1
7
If the default gateway is configured incorrectly on the host, what is the impact on communications?
The host is unable to communicate on the local network.
**The host can communicate with other hosts on the local network, but is unable to communicate with hosts on remote networks.
The host can communicate with other hosts on remote networks, but is unable to communicate with hosts on the local network.
There is no impact on communications.
8
What is the purpose of a default gateway?
physically connects a computer to a network
provides a permanent address to a computer
identifies the network to which a computer is connected
identifies the logical address of a networked computer and uniquely identifies it to the rest of the network
**identifies the device that allows local network computers to communicate with devices on other networks
9
What type of routing uses information that is manually entered into the routing table?
dynamic
interior
**static
standard
10
When the destination network is not listed in the routing table of a Cisco router, what are two possible actions that the router might take? (Choose two.)
**The router sends an ARP request to determine the required next hop address.
The router discards the packet.
The router forwards the packet toward the next hop indicated in the ARP table.
**The router forwards the packet to the interface indicated by the source address.
The router forwards the packet out the interface indicated by the default route entry.
11
What are the key factors to consider when grouping hosts into a common network? (Choose three.)
**gateways
purpose
physical addressing
software version
**geographic location
**ownership
12
What is a component of a routing table entry?
the MAC address of the interface of the router
the destination Layer 4 port number
the destination host address
**the next-hop address
13
Which intermediary devices could be used to implement security between networks? (Choose two.)
**router
hub
switch
**firewall
access point
bridge
14
What are three common problems with a large network? (Choose three.)
too few broadcasts
**performance degradation
**security issues
**limited management responsibility
host identification
protocol compatibility
15
Refer to the exhibit. All devices shown in the exhibit have factory default settings. How many broadcast domains are represented in the topology that is shown?
3
**4
5
7
8
11
16
Which three statements are true about routes and their use? (Choose three.)
If no route to the destination network is found, the packet is returned to the previous router.
If the destination network is directly connected, the router forwards the packet to the destination host.
**If multiple network entries exist for the destination network, the most general route is used to forward the packet.
**If no route exists for the destination network and a default route is present, the packet is forwarded to the next-hop router.
**If the originating host has a default gateway configured, the packet for a remote network can be forwarded using that route.
If a host does not have a route manually configured for the destination network, the host will drop the packet.
17
Refer to the exhibit. A network administrator is troubleshooting a connectivity problem and needs to determine the address that is used to forward network packets out the network. Using the netstat -r command, the administrator would identify which address as the address to which all hosts send packets that are destined for an outside network?
10.10.10.26
127.0.0.1
**10.10.10.6
10.10.10.1
224.0.0.0
18
Refer to the exhibit. A network administrator notices that there are too many broadcasts on the network. What two steps can the network administrator take to resolve this problem? (Choose two.)
**Replace S2 with a router.
Place all servers on S1.
Disable TCP/IP broadcasts.
**Subnet the 192.168.0.0 /24 network.
Disable all unused interfaces on the switches.
19
Refer to the exhibit. The network in the exhibit is fully operational. What two statements correctly describe the routing for the topology that is shown? (Choose two.)
**192.168.0.2 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 network to the 172.16.0.0 network.
10.0.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 10.0.0.0 network.
**192.168.0.1 is the next-hop address that is used by R1 to route a packet from the 192.168.12.0 network to the 172.16.0.0 network.
172.16.0.1 is the next-hop address that is used by R3 to route a packet from the 10.0.0.0 to the 172.16.0.0 network.
192.168.0.1 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
192.168.0.2 is the next-hop address that is used by R2 to route a packet from the 172.16.0.0 network to the 192.168.12.0 network.
20
What two characteristics are commonly associated with dynamic routing protocols? (Choose two.)
require no device configuration
**provide routers with up-to-date routing tables
require less processing power than static routes require
consume bandwidth to exchange route information
**prevent manual configuration and maintenance of the routing table
21
What statement describes the purpose of a default route?
A host uses a default route to transfer data to another host on the same network segment.
A host uses a default route to forward data to the local switch as the next hop to all destinations.
A host uses a default route to identify the Layer 2 address of an end device on the local network.
**A host uses a default route to transfer data to a host outside the local network when no other route to the destination exists.
Langganan:
Postingan (Atom)
